...
The emtrion SBC is a platform based on the Renesas RZN1D cpu. It consists of a CM3 core and a A7 core. For the CM3 core a firmware containing PROFINET, EtherNet/IP and EtherCAT stack is available. Ethernet ports J8 and J9 are exclusively used by the CM3 core. Ethernet ports J1 and J2 are exclusively used by linux.
Required resources
...
Emtrion SBC
...
24 V power adapter
...
USB Serial converter
...
Network cables
...
a ARM (arm-none-eabi) gcc compiler (e.g. version 9.2.1 20191025)
...
optionally the Emtrion SBC SDK: https://cloud.emtrion.de/index.php/s/Fd7XWdmjZrBlOhI
...
Emtrion hardware documentation (SBC-RZN1D-Hardware_Manual_v008en.pdf)
...
Emtrion SDK and software documentation (sbc-rzn1d-yocto-manual_v005en.pdf)
...
updated device tree
...
updated uboot
...
cm3 firmware
...
Features
features on par with port’s SoM module, while providing better performance due to parallel connection between host CPU (A7/Linux) and CM3 core
full featured embedded linux system with additional communication core (SoM like)
PROFINET, EtherNet/IP and EtherCAT support
Limitations
The currently delivered CM3 firmware has following restrictions:
firmware update functionality from A7 or over Ethernet (HTTP, EtherCAT) not implemented, required to do using u-boot
Exception Log not supported
CM3 reset not possible, a restart of the A7 application requires reboot of the whole system
Required resources
Emtrion SBC
24 V power adapter
USB Serial converter
Network cables
a ARM (arm-none-eabi) gcc compiler (e.g. version 9.2.1 20191025)
optionally the Emtrion SBC SDK: https://cloud.emtrion.de/index.php/s/Fd7XWdmjZrBlOhI
Emtrion hardware documentation (SBC-RZN1D-Hardware_Manual_v008en.pdf)
Emtrion SDK and software documentation (sbc-rzn1d-yocto-manual_v005en.pdf)
updated device tree
updated uboot
cm3 firmware
port application sdk
Industrial Communication Explorer
Device setup
Entering the boot loader
You will need a USB serial converter connected to the device (header J5). UART speed is 115200 baud. After bootup of the device you will have the possibility to enter the uboot boot loader. From there the following steps can be executed.
Update of uboot
Please refer to the documentation from emtrion (sbc-rzn1d-yocto-manual_v005en.pdf) on how to update the uboot boot loader (u-boot.img). This is possible using a NFS or a TFTP server. The correct version shown should be “U-Boot 2017.01 sbc-rzn1d v01.0xp (Feb 02 2021 - 11:46:11 +0000)
”.
Update of the device tree
Now you need to boot into linux (power cycle or u-boot command "boot"). The device is initially configured to use DHCP. Ethernet ports J1 and J2 are used by the linux system. To login into linux, use the account root with no password (default settings).
Please place the dtb into the /boot folder of the filesystem accessible within linux.
Programming of the CM3 firmware
Delivery
The port SDK is provided in the form of an zip archive. Beside the sources required for building applications for the protocol stacks and some examples following files are provided:
CM3 firmware: projects/2021015/cc/dtb/cm3_fw.bin
this is the firmware for the CM3 core containing the protocol stacks
DTB: projects/2021015/cc/dtb/sbc-rzn1d.dtb
this is the device tree for the A7 (Linux) core required to fully support the CM3 core functionality
Device setup
Entering the boot loader
You will need a USB serial converter connected to the device (header J5). UART speed is 115200 baud. After bootup of the device you will have the possibility to enter the uboot boot loader. From there the following steps can be executed.
Programming of the CM3 firmware
This step is done from the u-boot bootloader. Following commands show the procedure. Update is done using tftp here:
...
Code Block |
---|
SBC-RZN1D U-Boot > run update_cm3 Speed: 1000, full duplex Using dwmac.44002000 device TFTP from server 192.168.2.1; our IP address is 192.168.2.2 Filename '/private/tftpboot/cm3_fw.bin'. Load address: 0x80008000 Loading: ############# 3.4 MiB/s done Bytes transferred = 180287 (2c03f hex) SF: Detected s25fl128s_64k with page size 256 Bytes, erase size 64 KiB, total 16 MiB, mapped at 10000000 SF: 196608 bytes @ 0xe0000 Erased: OK device 0 offset 0xe0000, size 0x2c03f SF: 180287 bytes @ 0xe0000 Written: OK |
...
Update of the
...
device tree
Now you need to boot into linux (power cycle or u-boot command "boot"). The device is initially configured to use DHCP. Ethernet ports J1 and J2 are used by the linux system. To login into linux, use the account root with no password (default settings).
Please place the dtb into the /boot folder of the filesystem accessible within linux.
Setup of the port SDK
The port SDK can be be used on any linux machine capable of cross compiling for the arm platform (see compiler requirements). To install the SDK create a folder and unpack the delivered archive (0860_012_SDK_2_23_0__EMTRIONSBC_LINUX_GCC.zip).
To compile a profinet example application, do the following steps:
...
Code Block |
---|
make CROSS_COMPILE=/opt/toolchain/armv8arm-rpi3linux-linuxgnuebaihf-gnueabihfgcc/bin/armv8-rpi3arm-linux-gnueabihf- |
The resulting binary is located in the sub folder build/emtrion_sbc_rzn1d_a7. It can be transfered to the device using scp:
...
Code Block |
---|
root@sbc-rzn1d:~# ./goal_emtrion_sbc_rzn1d_a7.bin GOAL Start mbox: Created device mbox_2. [AC_I|goal_taskCreate:117] creating task: GOAL Timer [AC_I|goal_tgtTaskCreate:1210] task stack size: 8388608 byte [AC_I|goal_tgtTaskCreate:1252] task scheduler priority: 99 [AC_I|goal_taskCreate:160] Created task GOAL Timer with priority 100/100 and stack 0 byte sucessfully. [AC_I|goal_cmInit:220] Calculated config size of 240 in 3 modules modules [AC_I|goal_taskCreate:117] creating task: /dev/mbox_2 [AC_I|goal_tgtTaskCreate:1210] task stack size: 8388608 byte [AC_I|goal_tgtTaskCreate:1252] task scheduler priority: 54 [AC_I|goal_taskCreate:160] Created task /dev/mbox_2 with priority 50/100 and stack 0 byte sucessfully. [AC_I|goal_miMctcRamReg:148] setting media timeout to 1000: [AC_I|goal_miDmPartRegInt:275] part added to 'Read from CC', pos: 1159, len: 4296 [AC_I|goal_miDmPartRegInt:275] part added to 'Write to CC', pos: 1159, len: 4296 [AC_I|goal_snmpInitRpc:103] SNMP Application Core successfully started [AC_I|goal_taskCreate:117] creating task: GOAL Main [AC_I|goal_tgtTaskCreate:1210] task stack size: 8388608 byte [AC_I|goal_tgtTaskCreate:1252] task scheduler priority: 10 [AC_I|goal_taskCreate:160] Created task GOAL Main with priority 0/100 and stack 0 byte sucessfully. [AC_I|goal_init:181] GOAL initialized [AC_I|goal_miMctcRpcSyncLoop:1208] RPC state synchronized, running appl_setup [AC_I|goal_miMctcRpcSyncLoop:1212] configuring timeout values for peer [AC_I|goal_pnioNewAc:264] auto data mapper for DP is disabled [AC_I|goal_pnioNewAc:265] auto data mapper for APDU is disabled [AC_I|goal_pnioNewAc:339] PROFINET Application Core successfully started [AC_I|appl_setup:239] Initializing device structure [AC_I|goal_miDmPartRegInt:275] part added to 'Write to CC', pos: 0, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Read from CC', pos: 0, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Write to CC', pos: 1, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Read from CC', pos: 1, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Write to CC', pos: 2, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Read from CC', pos: 2, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Write to CC', pos: 3, len: 2 [AC_I|goal_miDmPartRegInt:275] part added to 'Read from CC', pos: 3, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Write to CC', pos: 5, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Read from CC', pos: 4, len: 2 [AC_I|goal_miDmPartRegInt:275] part added to 'Write to CC', pos: 6, len: 1 [AC_I|goal_miDmPartRegInt:275] part added to 'Read from CC', pos: 6, len: 1 [AC_I|appl_setup:456] PROFINET ready [AC_I|appl_setup:458] Configuring DD [AC_I|appl_setup:482] DD ready [AC_I|appl_httpSetup:100] setup web server [AC_I|goal_httpNewAc:954] HTTP Application Core successfully started [AC_I|appl_httpSetup:178] web server setup done [AC_I|appl_setup:504] CCM version : 2ab72cd22 [AC_I|appl_setup:505] CCM device : 1 [AC_I|appl_setup:507] CCM Serial : 01:00:00:00:8c:e2 [AC_I|goal_miMctcRpcSyncLoop:1253] local setup done [AC_I|goal_memInitDone:152] fixed memory usage: 109916/262144 bytes bytes [AC_I|goal_memInitDone:157] fixed memory usage: (42%) |
...
Automatic start of the
...
The Industrial Communication Explorer is a management tool including PLC capabilities for EtherCAT, PROFINET and EtherNet/IP. Please refer to it’s documentation for installation and usage:
https://portgmbh.atlassian.net/wiki/spaces/ICE
Example Applications
Limitations
The currently delivered CM3 firmware has following restrictions:
...
time limited to 180 minutes
...
MAC address is fixed at 0x02:00:00:00:00:01
...
EtherCAT support is missing
...
not fully tested, no conformance testing done
...
LED support not fully implemented, LED colors on the hardware limit possible protocol conformance (EtherCAT, EtherNet/IP)
...
firmware update functionality from A7 or over Ethernet (HTTP, EtherCAT) not implemented, required to do using u-boot
...
Exception Log not supported
...
firmware
There is an init script /etc/init.d/goal_app.sh provided, which if a binary under /home/root/goal_emtrion_sbc_rzn1d_a7.bin is available, this is started at boot time.
Installation of the port Industrial Communication Explorer
The Industrial Communication Explorer is a management tool including PLC capabilities for EtherCAT, PROFINET and EtherNet/IP. Please refer to it’s documentation for installation and usage:
https://portgmbh.atlassian.net/wiki/spaces/ICE
Example Applications
Frequently asked questions
How to configure static IP configuration for the linux ethernet interface? | The initial ip configuration of the interface eth0 is configued in u-boot (see emtrion manual).
If IP configuration shall be done through linux, clear all uboot variables related to IP address:
If done so, a static IP address or DHCP can be enabled through an init script. | ||||
How to automatically start an application. | Put application into home folder /home/root under name goal_rzn1d_a7_linux.bin. After a reboot the application will be started automatically. | ||||
How to disable waiting for network connection during startup of the device. | Once all IP address related variables in uboot are deleted, this check is disabled. |