Porting Paulus on infineon XMC4800

File structure

After installation of Paulus the source code is stored in the file structure shown in Table 1 describes the contents.

Table 1: description of directories

The initialization of the CAN controller is done in module xmc4800/ can.c.

In module xmc4800 / init.c the I/O pins for the CAN interface have to be initialized.

In module xmc4800/ init.c there must be the functions getBitRate() and getNodeId() available. Usually the CANopen network parameters are provided by reading jumpers or by loading from flash memory.

Development environment

Paulus on the platform of infineon xmc4800 was developed with the infineon Dave4 studio v4.5 on Board infineon Automation KitV2.

Paulus configuration

In general the initialization function initializes only the absolutely necessary peripherals like clock system, CAN controller, memory management as needed by Paulus and a timer for Heartbeat or LSS. Nevertheless, there might be situations where it makes sense that Paulus initializes other functionalities which are later used by the application as well. As an example consider the serial interface for debug messages.

CAN bit rate

The CAN bit rate is coded by the index of the CAN bit timing table according to /CiA-305/. The index of the default CAN bit rate is specified about the compiler-define BITRATE_INDEX_<bit_rate> in / xmc4800 /bl_config.h:

#define BL_USED_BITRATE_INDEX   BITRATE_INDEX_125K

The default CAN bit rate is 125 kbit/s and can be changed by LSS services. The LSS services are described in /Paulus_man/ and base on /CiA-305/. The supported CAN bit rates are depending on the clock of the CAN controller and are listed in /xmc4800/xmc4800 _can.c. The value FFh for segment2 marks unsupported CAN bit rates. The clock for the activation of the CAN bit rate is generated by timer Systick with a period of 1 ms.

Heartbeat producer

Timer Systick is also used for the generation of Heartbeat producer messages.

Read Identity object 0x1018 from NVM

If the user needs the values for the identity object from Paulus (Vendor-ID, Product code, Revision number, Serial number) in different devices with different values then the following define must be activated.

#define BL_IDENTITY_OBJECT_1018_READ_FROM_NVM

If this activated, in the startup from Paulus the data for this object are read from a predefined flash area. The address from this area is defined:

#define BL_CONF_IDENTITY_BLOCK     0xC1C0000 /* default address */

The user must ensure that his desired data is written on this address. This is possible for example with a Flash Programmer tool.

Debug output

By the compiler-define BL_DEBUG a debug output is prepared but not implemented. The compiler-define is set in file /xmc4800 /bl_config.h:

#define BL_DEBUG 1

In general the initialization function will initialize only the absolutely necessary peripherals like clock system, CAN controller, memory management as needed by Paulus. Nevertheless, there might be situations where it makes sense that Paulus initializes other functionalities which are later used by the application as well. As an example consider the serial interface for debug messages.

Generating application software

The application software consists of an application header and an application program, see Figure 2.

Open

Figure 1: structure of application software

The application program has to be prepared for download by the following steps:

•  build the application program in binary format

• calculate the CRC of the application program, build the application header and generate the application software to download

• configure the start address of the application software in Paulus

Paulus checksum

The program paulus_cksum calculates the CRC checksum of the binary application program generates
the application header and stores the application header and the application program in a new file. This
file can be loaded in the device by Paulus.
Unused bytes in the application header are set to 0x00 with the xmc4800. The length of the application
header is 0x200 bytes. The input file (s1_xmc4800_dave4.bin) for this tool is the generated binary output
from the infineon Dave4 Studio (build outputfile format “binary”).
Example: The download file for the application program s1_xmc4800_download.bin is generated about
Windows console:

Besides checking the CRC Paulus checks also the size of the application header. A size of 0 is invalid. An application may destroy the ’valid’ information by overwriting the size with 0. That is always possible on the xmc4800 FLASH, because the byte content is 0x00 after erasing.

More detailed information from this tool can find in /Paulus_CRC/.

Start address

It is important that the start address of the application software in the flash memory and the information in the Paulus configuration in xmc4800/xmc4800_flash.h are identical. The application software is stored as a separate program in the flash memory additionally to the bootloader program. Therefore the application software is flashed to:

#define FLASH_PROGRAM_START_ADR   0xC010000u // default configuration

The length of the application header is 0x200 byte. The real program start of the application is at address (FLASH_PROGRAM_START_ADR + 0x200 bytes).

Memory

Shared RAM

The shared RAM for data exchange between bootloader and application starts at address 0x2001FF00. The size of the shared RAM is specified in xmc4800/bl_interface.h by the compiler-define BL_JUMPCODE_SIZE. The shared memory is installed in xmc4800/bl_interface.h as follow:

/* jumpcode placed on ram adress 0x2001FF00 */

__attribute__((section (".myRAMSection"))) UNSIGNED8 jumpcode[BL_JUMPCODE_SIZE];

The keyword for the re-start of the application program is set in byte 0-3 of jumpcode. Paulus uses the keyword “APPL” or “BOOT” to start the application program, see /Paulus_man/.

Flash

The total size of the xmc4800 flash is 2Mb. The current implementation of Paulus occupies a memory area
of 64Kb from this. Therefore 1984Kb (less 0x200 byte crc header) flash memory area available for the
application software.

Figure 2: Flash memory mapping

Open

On power-on, as soon as execution control goes to the default reset handler, the boot up sequence
executes and execution control jumps to the user boot code. The boot code always starts in the paulus, this
decides whether the application is started.
The flash area for LSS configuration data of Paulus is located at address 0xC1C0000 (last section: default
address, adaptable by user). On this address and the following Paulus stores the node-ID and the CAN bit
rate index during the execution of the LSS service “LSS store configuration“. The addresses are
configurable in <target>/bl_interface.h:
#define FLASH_ADDRESS_NODEID 0xC1C0000
#define FLASH_ADDRESS_BITRATE_INDEX 0xC1C0001

/* additional need some bytes in RAM for NodeId and bitrateIndex saved in a special section */

__attribute__((section (".myRAMSection"))) UNSIGNED8 flashNodeId=0xFF;

__attribute__((section (".myRAMSection"))) UNSIGNED8 bitrateIndex=0xFF;

After the next re-start Paulus uses this node-ID and this CAN bit rate index for communication. The new CAN bit rate cannot be activated by NMT-Command Reset Application. If the LSS services are not used, Paulus uses the node-ID and CAN bit rate index configured in xmc4800/bl_config.h.

For the additional feature “Read Identity object 0x1018 from NVM” the following struct is prepared:

The Paulus fills this struct in startup with the data from the predefined flash area. Starting at address
0xC180000 and following (4 x u32 values). Previously the data was written on these addresses e.g. via a
simple write operation in the Dave4 Debug session:

After reading the data in the struct these are used for CANopen communication (e.g read items from object 0x1018 - especially for the LSS service).

Example application 

CANopenSlave1 is an example for an application program. The directory example/ CANopenSlave1_XMC4800/examples/s1_xmc4800 contain the compiler project and the application-specific functions. For compilation the CANopen Library and the suitable driver package is necessary. The CANopen Library and the driver package belong not to the delivery scope of Paulus. The binary application software in example/ CANopenSlave1_XMC4800/bin/s1_xmc4800_download.bin can be used for a quick start.

The linker file of this example project is adapted on these memory requirements.

See settings in linker-file ((linker_script.ld) from example:

This example has included source files bl_interface.c, bl_interface.h from bootloader. The application program can request an update by jumping back into Paulus by writing of the program control command start application program (value 1) on object 1F51h/1. The application program calls the macro BOOTLOADER_JUMP(APPL). This call is implemented in usr_301.c /sdoWrInd(). The application program stores the keyword “APPL” in the shared RAM and jumps into Paulus. Paulus is re-started and stays running until the application program is started by command.

References

 Table 2: References