Page Comparison

...

Set the Vendor ID of this EtherNet/IP stack instance. The vendor ID is assigned by the ODVA.

Default Value: 1114

goal_eipCfgVendorIdSet parameters

Table: goal_eipCfgVendorIdSet parameters

res = goal_eipCfgVendorIdSet(1114);

goal_eipCfgDeviceTypeSet

Set the Device Type of this EtherNet/IP stack instance. Valid values are defined by the CIP specification.

Default Value: 0x2B

goal_eipCfgDeviceTypeSet parameters

Table: goal_eipCfgDeviceTypeSet parameters

res = goal_eipCfgDeviceTypeSet(0x2B);

goal_eipCfgProductCodeSet

Set the Product Code of this EtherNet/IP stack instance. This value is defined by the device vendor.

Default Value: 1goal_eipCfgProductCodeSet parameters

Table: goal_eipCfgProductCodeSet parameters

res = goal_eipCfgProductCodeSet(0xABCD);

goal_eipCfgRevisionSet

Set the Revision of the EtherNet/IP stack instance. The revision consists of a major and a minor number. It represents changes in the firmware that affect the device’s behaviour.

Default Value: 1.1

goal_eipCfgRevisionSet parameters

Table: goal_eipCfgRevisionSet parameters

res = goal_eipCfgRevisionSet(1, 3);

goal_eipCfgSerialNumSet

Set the Serial Number of the EtherNet/IP stack instance. This number is assigned by the vendor and should be unique for each device.

Default Value: 1

goal_eipCfgSerialNumSet parameters

Table: res = goal_eipCfgRevisionSet(1, 3);

res = goal_eipCfgSerialNumSet(12345678);

goal_eipCfgProductNameSet

...

Default Value: “EtherNet/IP Adapter”

goal_eipCfgProductNameSet parameters

Table: goal_eipCfgProductNameSet parameters

res = goal_eipCfgProductNameSet("EtherNet/IP Adapter");

goal_eipCfgDomainNameSet

Set the default Domain Name of the EtherNet/IP stack instance. This name is used as the device’s domain name if no valid configuration was found. Its maximum length is 48 characters.

Default Value: “port.de”

goal_eipCfgDomainNameSet parameters

Table: goal_eipCfgDomainNameSet parameters

res = goal_eipCfgDomainNameSet("example.org");

goal_eipCfgHostNameSet

Set the default Host Name of the EtherNet/IP stack instance. This name is used as the device’s host name if no valid configuration was found. Its maximum length is 64 characters.

Default Value: “eipdevice”

goal_eipCfgHostNameSet parameters

Table: goal_eipCfgHostNameSet parameters

res = goal_eipCfgHostNameSet("example_device");

goal_eipCfgNumExplicitConSet

Set the maximum number of explicit Connections the device can handle at once.

Default Value: 6

goal_eipCfgNumExplicitConSet parameters

Table: goal_eipCfgNumExplicitConSet parameters

res = goal_eipCfgNumExplicitConSet(10);

goal_

...

eipCfgNumImplicitConSet

Set the maximum number of implicit Connections the device can handle at once.

Default Value: 6

goal_eipCfgNumImplicitConSetImpl parameters

Table: goal_eipCfgNumImplicitConSet parameters

res = goal_

...

eipCfgNumImplicitConSet(10);

goal_eipCfgEthLinkCountersOn

Enable support for Ethernet Link attributes 4, 5, 12 and 13. THe The hardware must support the appropriate counters.

Default Value: GOAL_TRUEgoal_eipCfgEthLinkCountersOn parameters

Table: goal_eipCfgEthLinkCountersOn parameters

res = goal_eipCfgEthLinkCountersOn(GOAL_TRUE);

goal_eipCfgEthLinkControlOn

Enable support for Ethernet Link attribute 6. The hardware must support forced link speeds and duplex modes.

Default Value: GOAL_TRUEgoal_eipCfgEthLinkControlOn parameters

Table: goal_eipCfgEthLinkControlOn parameters

res = goal_eipCfgEthLinkControlOn(GOAL_TRUE);

goal_eipCfgChangeEthAfterResetOn

A change of Ethernet link speeds or duplex modes requires a reset of the device. The hardware must support forced link speeds and duplex modes.

Default Value: GOAL_FALSEgoal_eipCfgChangeEthAfterResetOn parameters

Table: goal_eipCfgChangeEthAfterResetOn parameters

res = goal_eipCfgChangeEthAfterResetOn(GOAL_FALSE);

goal_eipCfgChangeIpAfterResetOn

A change of the IP address requires a reset of the device.

Default Value: GOAL_FALSEgoal_eipCfgChangeIpAfterResetOn parameters

Table: goal_eipCfgChangeIpAfterResetOn parameters

res = goal_eipCfgChangeIpAfterResetOn(GOAL_FALSE);

goal_eipCfgNumSessionsSet

Set the number of Encapsulation sessions the device can handle at once.

Default Value: 20goal_eipCfgNumSessionsSet parameters

Table: goal_eipCfgNumSessionsSet parameters

res = goal_eipCfgNumSessionsSet(10);

goal_eipCfgTickSet

Set the number of milliseconds of one tick. The stack uses a tick as the smallest unit of time.

Default Value: 10

goal_eipCfgTickSet parameters

...

Parameter

...

Description

...

uint32_t ticks

...

size of 1 tick in ms

...

Info
This function is deprecated and has no effect. It is kept for compatibility with older versions.

goal_eipCfgO2TRunIdleHeaderOn

...

Enable the Run/Idle Header for consumed (Originator-to-Target) cyclic data.

goal_eipCfgO2TRunIdleHeaderOn parameters

Table: goal_eipCfgO2TRunIdleHeaderOn parameters

res = goal_eipCfgO2TRunIdleHeaderOn(GOAL_TRUE);

goal_eipCfgT2ORunIdleHeaderOn

Enable the Run/Idle Header for produced (Target-to-Originator) cyclic data.

Default Value: GOAL_FALSE

goal_eipCfgT2ORunIdleHeaderOn parameters

Table: goal_eipCfgT2ORunIdleHeaderOn parameters

res = goal_eipCfgT2ORunIdleHeaderOn(GOAL_FALSE);

goal_eipCfgQoSOn

Enable support of the QoS object.

Default Value: GOAL_TRUEgoal_eipCfgQoSOn parameters

Table: goal_eipCfgQoSOn parameters

res = goal_eipCfgQoSOn(GOAL_TRUE);

goal_eipCfgNumDelayedEncapMsgSet

Set the number of Encapsulation messages that can be delayed at the same time.

Default Value: 2goal_eipCfgNumDelayedEncapMsgSet parameters

Table: goal_eipCfgNumDelayedEncapMsgSet parameters

res = goal__eipCfgNumDelayedEncapMsgSet(2);

goal_eipCfgDhcpOn

Enable the DHCP client if it is supported by the platform.

Default Value: GOAL_FALSEgoal_eipCfgDhcpOn parameters

Table: goal_eipCfgDhcpOn parameters

res = goal_eipCfgDhcpOn(GOAL_TRUE);

goal_eipCfgDlrOn

Enable support of the DLR object. THis This feature requires the DLR stack and support of the hardware.

Default Value: GOAL_FALSE

Table: goal_eipCfgDlrOn parameters

res = goal_eipCfgDlrOn(GOAL_TRUE);

goal_eipCfgAcdOn

Enable support for Address Conflict Detection (ACD).

Default Value: GOAL_FALSE

Table: goal_eipCfgAcdOn

res = goal_

...

eipCfgAcdOn(GOAL_TRUE);